Filters

3 kW (4 HP), 230/400V, 3 phase

KOMO KOMO VR-512-TG, 3-AXIS 5 FT x 12 FT 3 axis router CNC ROUTER (04/2006), (480/60/3, 33.79 FLA electrics), S-4731 Standard Specifications: - 5’ x 12' vacuum table - 12 HP, 24,000 RPM HSK router...

Multicam Model Digital Express D-204-K-HS 10982 5x10 table new 2015 Specifications IZ-Axis Clearance 2” Z-Axis Travel 5” Repeatability +/-0.001” +/-0.025mm Cutting Speed 4000 IPM 76.2 MPM...

Specifications 5'x10' Moving Gantry with a machined aluminum Table Single-zone acrylic vacuum plenum, and manual Pop-up Pins Features: 122" X 74.2" Y axis travel High Performance closed loop AC Ser...

MACHINE: •Fixed table, moving gantry, three-axis configuration •Ultra-rigid, tab welded structural steel base and bridge, fully stress relieved •Highly efficient 61 inch wide by 121 inch deep steel...

14'' x 28'' sealing area no feeds automatic takeoff new 2015

DMS Model D5E - 5O5-4-3-32S Enclosed 5 Axis Single Table CNC Router with 4'Wx3'D Aluminum Fixture Table - 32 Inch Z Axis Stroke and Bridge Clearance, 6.2 Hp. ISO30 Spindle, 10 Pocket Rack Style Aut...

Model: VT-2500-LS Heater kW : 10 Process Pump HP : 5 GPM : 90 PSI : 34 Full Load Amperage 230/3/60 : 36.6 460/3/60 : 18.3 575/3/60 : 15.3 Connection Sizes To Process : 2" From Process : 2" W...

Multicam MG205 CNC Router -5'x12', vacuum bed -13" z-travel, 8" gantry clearance -12HP GC Colombo ATC spindle -8-position tool carousel -Runs on 460V 3-phase but comes with transformer for use wi...

Komo VF 5’ X 12’ CNC router GE Fanuc 210i-M CNC Controls Vacuum Table, 8 Position Automatic Tool Changer. new 2002 GENERAL SPECIFICATIONS Axis Travels: 145” X 84” X 9” Max Spindle RPM: 16,000 F...

Used Multicam 3000 5' x 10' CNC router Series 3000 5' x 10' table Model 204 R new 2015 ATC

KOMO 2006 VR-512-TG, 5’ x 12’ MOVING GANTRY CNC ROUTER Standard Specifications: - 5’ x 12' vacuum table - 12 HP, 24,000 RPM HSK router spindle - (10) stat...

new 2008 60" x 145" Fixed table, moving gantry machine in a front-to-back configuration 8"Z vacuum table supported by a 20 HP vacuum system . Equipped with: (1) 10 HP HSK COLOMBO Routing spindle w...

- Programmable and controlled 5 axis motion - High Performance high reliability brushless AC Servo Drive System with high acceleration and deceleration rates and feed speeds to 1500 inches/ minute ...

Multicam 3-205-R Router

Multicam Digital Express Router CNC Router

 12x 16 heat seal area  16x 20 nesting tray size (16 required for 1 set tooling)  3 feeders 1 before load, 2 after load  0-20 cycles per minute via AC variable frequency drive  Slide style eje...

Motion Master 4' x 8' 3 axis CNC router

Komo 508

Komo 510

KOMO VF 512 ROUTER WITH GE FANUC SERIES 210-i-M CNC CONTROL

3 Axis CNC Router

Used 2006 Frog 4' x 8' 3 Axis CNC Router

Used 2011 AXYZ Z7 Camtech CNC Router

Used Busch 016 vacuum pump 3/4 hp.

48'' x 96'' Table

Multicam series 3000 5' x 14' cnc router new 2013

AXYZ 6x16 3 axis CNC router 6' x 16' table new 2010 becker vacuum pump see videos below

2015 Laguna 60" X 120" Smart Shop 1 Series CNC Router